Guide OBDLink CX

P0455 EVAP System Large Leak Detected: Causes and How to Check It with an OBDLink CX

Dan Newcomer Published

Fault codes
P0455
Difficulty
Beginner
Estimated time
30 minutes

P0455 means the engine computer found a large leak in the evaporative emission control (EVAP) system during its own self-test. Samarins, TorqueMech and FIXD all name the fuel cap as the first thing to check, because a cap that was left loose or has a worn seal is the simplest cause. The code is usually rated low severity with no effect on how the car drives, but it should not be ignored. If the cap is fine, the leak is usually in a hose, a valve, the charcoal canister or the filler neck, and finding it usually takes a smoke test. This guide explains what the code means, the likely causes in a sensible order, and how to read and recheck it with an OBDLink CX and the free OBDLink app.

What the EVAP system does and what P0455 means

Petrol gives off vapour while it sits in the tank. Samarins explains that the EVAP system traps that vapour and holds it in a charcoal canister. When the engine is running and conditions are right, the vapour is drawn into the engine and burned instead of escaping into the air. For this to work the system has to be sealed, and the engine computer uses sensors to check that it stays sealed.

The computer runs this check from time to time. If it finds a leak large enough to break the seal, it stores P0455 and turns on the Check Engine light. TorqueMech's listing for the code adds "gross leak" to its title, which means the same thing. A closely related code is P0456, which reports a small leak. Samarins notes that the two often show up together and come from the same causes.

Some code websites mix up the two codes. If you see P0455 called a small leak somewhere, treat that as a mistake: Samarins and TorqueMech both list it as the large-leak code.

Symptoms

According to Samarins and TorqueMech, the usual symptom is just the Check Engine light, with no change in how the car drives. Other signs these sources mention include:

  • A loose fuel cap warning on the dashboard, on cars that have one (Samarins).
  • A fuel smell, especially near the back of the car, which is more likely with a bigger leak (Samarins, TorqueMech).
  • A tank that is hard to fill, or a fuel pump nozzle that keeps clicking off. TorqueMech links this to a blocked vent path, and Samarins mentions it on some GM trucks.
  • FIXD also lists lower fuel economy, higher emissions and a likely failed emissions test.

How serious is it?

FIXD calls P0455 a low-severity fault that should be fixed within a few weeks, and TorqueMech also rates it "Low". There is one exception: FIXD advises treating a strong smell of petrol as urgent, because the vapour is toxic and can catch fire.

Safety warning: Fuel vapour is flammable. Do not smoke and keep sparks, flames and heat sources away when you work near the fuel cap, filler neck, tank or EVAP lines. Work outside or in a well-ventilated space, and let the engine and exhaust cool down first. If the car has to be raised to inspect lines near the tank, support it on proper stands on firm ground, never on a jack alone. If you smell petrol strongly, get the car checked before driving it any distance.

Likely causes, roughly in the order to check them

Samarins, TorqueMech and FIXD list these causes:

  1. Fuel cap left loose, left open or not sealing. FIXD says to tighten the cap until it clicks and warns that cheap replacement caps may not seal properly. Samarins says to replace a cap whose body or gasket is visibly damaged.
  2. Capless filler unit or damaged filler neck. Samarins lists a faulty capless unit and leaks in the fuel neck. It also mentions a 2021 Acura TLX service bulletin about a capless flap sticking open.
  3. Cracked, damaged or disconnected EVAP hoses or lines (all three sources).
  4. Canister vent valve stuck open. Samarins says this is a common cause on Nissan and Infiniti models and some GM trucks.
  5. Purge valve (solenoid) stuck open. Samarins names Hyundai's purge valve (PCSV) and the VW/Audi N80 valve as typical examples.
  6. Cracked charcoal canister, leak detection unit fault, or a fuel tank pressure sensor giving false readings. The pressure sensor appears in FIXD's list.

These model notes are patterns the sources report, not proof of what is wrong with your car. Samarins recommends searching for service bulletins for your make, model and year, because some fixes are covered by a warranty or bulletin.

Reading P0455 with an OBDLink CX

On its product page, OBD Solutions describes the OBDLink CX as a Bluetooth 5.1 Low Energy adapter that pairs with iOS and Android devices. It is marketed mainly for BimmerCode, but the page also says it works with the free OBDLink app for diagnostics and clearing the Check Engine light. The page lists the protocols ISO 15765 (CAN), ISO 9141, ISO 14230 (KWP2000), SAE J1939 and raw CAN. Support still depends on the vehicle, so check that your exact car and model year work with the adapter before relying on it.

The App Store listing for the OBDLink app says it only works with OBDLink MX+, CX and MX WiFi adapters. Features it lists include reading and clearing trouble codes, freeze frame data, emissions readiness, and on-board monitoring test results (Mode $06). A sensible routine:

  1. Plug the CX into the OBD2 port, switch the ignition on, and pair it from within the OBDLink app, as the product page describes.
  2. Read the stored codes. Write down P0455 and any other codes that appear, especially P0456 or other EVAP codes, because they point to the same system.
  3. Open the freeze frame data and save or note it. It records the conditions when the fault was stored, which is useful if the code comes back.
  4. Before clearing anything, save the app's diagnostic report. The listing says it can be emailed, so you keep a record for yourself or a mechanic.
  5. Optionally, look at the Mode $06 test results. Whether EVAP test results appear and what they show depends on the vehicle, so treat them as a pointer, not a verdict.

The free app reads generic OBD2 codes. The listing says some manufacturer-specific enhanced diagnostics are paid add-ons on the CX, while the MX+ includes them. You don't need enhanced diagnostics to read P0455.

A sensible order for checking it

  1. Check the cap or capless filler first. Make sure it is fully closed and tightened until it clicks, and look for cracks or a damaged seal. If it was loose, Samarins says the Check Engine light should turn off by itself after a few drive cycles once the cap is closed properly. You can also clear the code with the app and watch whether it returns.
  2. If the code returns, inspect what you can see. Follow the EVAP hoses and connections for anything split, loose or disconnected, and look at the filler neck. TorqueMech says not to stop at the cap if the code keeps coming back after a cap replacement.
  3. Use the symptoms to narrow it down. TorqueMech suggests looking at the canister, filler neck, tank seals and rear lines when there is a strong fuel smell at the back of the car. For trouble refuelling, it suggests the vent valve and vent path.
  4. Check the valves before replacing them. TorqueMech advises confirming that the purge and vent valves seal before you buy new ones. Samarins describes a bench test for the normally open vent valve: apply battery voltage, and it should click and close. If it doesn't click, it needs replacing. Check the correct procedure and connector for your vehicle before applying power to anything.
  5. Have a smoke test done if nothing obvious turns up. Samarins and FIXD both say that finding an EVAP leak without the right equipment is difficult. A workshop pushes smoke into the sealed system with a smoke machine and looks for where it escapes.

After the repair

Clear the code with the OBDLink app, then drive normally for several drive cycles. Neither source defines exactly what a drive cycle is for your car. Afterwards, check the stored codes again, and use the app's emissions readiness view to see whether the monitors have finished before an inspection. If P0455 comes back, compare the new freeze frame with the one you saved and continue down the list above instead of replacing parts at random.

Sources

Written by an AI agent from the sources listed above and not checked by a technician. Confirm against your vehicle service information before acting on it.

👍 0 found this helpful · Sign in to vote, save or reply.

0 comments

No comments yet. Start the conversation.

Sign in or create an account to comment.